Does anyone have any input on using a die to trim the cases to length vs using a lathe like case trimming tool?
Does anyone have any input on using a die to trim the cases to length vs using a lathe like case trimming tool?
I cant say that one is better but just which you prefer. I like the LEE caselength guage tools. They thread into a hand held cutter and the mandrel will let you trim to exact length every time. Look in the Lee website for an Idea
pinne65 have both systems if you have the correct pilot the lathe style is probably the cleanest.
If you are doing real major brass alteration the file die is probably better.
Pick your poison and fly at her man one is as good as the other really.
Ken.
Ken.
Love to Live, Live to Shoot!
Live by the Gun...Die by the Gun...
it's speed vs exact
you can get really close or dead on with the lathe types but usually
more like in a tolerance range of 1or2 thou
with a power trimmer you can take a bit of brass off pretty quick.
File trim dies are "older technology", but are very accurate. Their downside is that they get brass shavings from the file into the workings of your press that have to be cleaned out. Cranking a lathe type trimmer for a large lot of cases can raise a few blisters; the systems are much improved by adding a power drill, and they are also very accurate if set correctly. Power trimmers are accurate, too, and may be the fastest method. Again, proper setup is critical. Lee trimmers are fast and easy, but may not produce as square a case mouth as other methods, but for hunting and most target ammo, it is not enough to cause any appreciable accuracy problems. If you have a rifle with a match chamber capable of better than .5MOA accuracy, then it may begin to be an issue, but for 99% of loading, the trimming method is irrelevant as long as you have some way to reduce the case length from max to trim-to for safe functioning.
"Stand your ground.
Do not fire unless fired upon.
But if they mean to have a war let it begin here."
- Capt. Parker, Lexington Militia, April 19, 1775
Ok,
I got the RCBS trimmer. Now I got blisters on my index finger. No J/K. The cases I trimmed are now within 0.0015" of each other. Is that what you would expect, better, worse?
that will be good enough for most any thing even counting measuring errors
you are as good as it needs to be
like versifier said
I wouldn't have any complaints there, either.
BTW, you can remove the crank handle and hook up an electric drill, a little rosin will help the chuck grip the round shaft better if necessary. I have done that for both my RCBS and my Lyman trimmers and saved a lot of wear and tear on my fingers.
"Stand your ground.
Do not fire unless fired upon.
But if they mean to have a war let it begin here."
- Capt. Parker, Lexington Militia, April 19, 1775
Ok,
When I get more cases and a better feel for the process I'll get a drill.
Thanks!
I'm not sure if the rcbs is like the lyman trimmer But I have found that the lyman is more accurate than that. If They are the same I would check and make sure that before you tighten the case holder mechanizm the case is firmly pushed all the way back. This way they are the same every time.
Nathan
Casting and reloading newbie
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |