Results 1 to 10 of 10

Thread: Case trimming die vs case trimming tool

  1. #1
    GunLoad Trainee
    Join Date
    Feb 2008
    Location
    Hillsboro/Oregon
    Posts
    15

    Default Case trimming die vs case trimming tool

    Does anyone have any input on using a die to trim the cases to length vs using a lathe like case trimming tool?

  2. #2
    GunLoad Trainee
    Join Date
    Mar 2008
    Location
    maryland
    Posts
    25

    Default trim

    I cant say that one is better but just which you prefer. I like the LEE caselength guage tools. They thread into a hand held cutter and the mandrel will let you trim to exact length every time. Look in the Lee website for an Idea

  3. #3
    Great Master kodiak1's Avatar
    Join Date
    Dec 2005
    Location
    Alberta Territory
    Posts
    309

    Default

    pinne65 have both systems if you have the correct pilot the lathe style is probably the cleanest.
    If you are doing real major brass alteration the file die is probably better.
    Pick your poison and fly at her man one is as good as the other really.
    Ken.
    Ken.

    Love to Live, Live to Shoot!
    Live by the Gun...Die by the Gun...

  4. #4
    runfiverun runfiverun's Avatar
    Join Date
    Dec 2007
    Location
    soda springs idaho
    Posts
    657

    Default

    it's speed vs exact
    you can get really close or dead on with the lathe types but usually
    more like in a tolerance range of 1or2 thou
    with a power trimmer you can take a bit of brass off pretty quick.

  5. #5
    Dogs Like Him versifier's Avatar
    Join Date
    Dec 2005
    Location
    New Hampshire
    Posts
    1,854

    Default

    File trim dies are "older technology", but are very accurate. Their downside is that they get brass shavings from the file into the workings of your press that have to be cleaned out. Cranking a lathe type trimmer for a large lot of cases can raise a few blisters; the systems are much improved by adding a power drill, and they are also very accurate if set correctly. Power trimmers are accurate, too, and may be the fastest method. Again, proper setup is critical. Lee trimmers are fast and easy, but may not produce as square a case mouth as other methods, but for hunting and most target ammo, it is not enough to cause any appreciable accuracy problems. If you have a rifle with a match chamber capable of better than .5MOA accuracy, then it may begin to be an issue, but for 99% of loading, the trimming method is irrelevant as long as you have some way to reduce the case length from max to trim-to for safe functioning.
    "Stand your ground.
    Do not fire unless fired upon.
    But if they mean to have a war let it begin here."
    - Capt. Parker, Lexington Militia, April 19, 1775

  6. #6
    GunLoad Trainee
    Join Date
    Feb 2008
    Location
    Hillsboro/Oregon
    Posts
    15

    Default

    Ok,

    I got the RCBS trimmer. Now I got blisters on my index finger. No J/K. The cases I trimmed are now within 0.0015" of each other. Is that what you would expect, better, worse?

  7. #7
    runfiverun runfiverun's Avatar
    Join Date
    Dec 2007
    Location
    soda springs idaho
    Posts
    657

    Default

    that will be good enough for most any thing even counting measuring errors
    you are as good as it needs to be
    like versifier said

  8. #8
    Dogs Like Him versifier's Avatar
    Join Date
    Dec 2005
    Location
    New Hampshire
    Posts
    1,854

    Default

    I wouldn't have any complaints there, either.

    BTW, you can remove the crank handle and hook up an electric drill, a little rosin will help the chuck grip the round shaft better if necessary. I have done that for both my RCBS and my Lyman trimmers and saved a lot of wear and tear on my fingers.
    "Stand your ground.
    Do not fire unless fired upon.
    But if they mean to have a war let it begin here."
    - Capt. Parker, Lexington Militia, April 19, 1775

  9. #9
    GunLoad Trainee
    Join Date
    Feb 2008
    Location
    Hillsboro/Oregon
    Posts
    15

    Default

    Ok,

    When I get more cases and a better feel for the process I'll get a drill.

    Thanks!

  10. #10
    Grunt drklynoon's Avatar
    Join Date
    Mar 2008
    Location
    Southern Georgia
    Posts
    35

    Default

    I'm not sure if the rcbs is like the lyman trimmer But I have found that the lyman is more accurate than that. If They are the same I would check and make sure that before you tighten the case holder mechanizm the case is firmly pushed all the way back. This way they are the same every time.
    Nathan

    Casting and reloading newbie

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check        

Gunloads.com Sponsored Links