Page 1 of 2 12 LastLast
Results 1 to 10 of 15

Thread: Tumbled Brass With Live Primers OK?

  1. #1
    GunLoad Trainee
    Join Date
    Feb 2011
    Posts
    8

    Question Tumbled Brass With Live Primers OK?

    I accidentally tumbled approximately 100 rounds of 30-30 brass that had new primers seated. I use corn cob media and the Dillon blue polishing compound in my tumbler. Should I kill the primers with oil, deprime and start over or should I just reload them and keep them separate so I know? I have them all set aside for now.

  2. #2
    GunLoad Trainee
    Join Date
    Nov 2009
    Posts
    4

    Default

    Hansj,

    First off let me say that I expect that you will get a wide range of answers.
    My guess is that most will be from those who got the bulk of their experience from the internet(read here:"I read online that").
    Now, take what I write as nothing more than one guy's experience from 50 years of stuffing cartridges-that does not make it correct or right or anything else, just what I have observed.
    There is a better than good chance that the primers will go bang every time.
    If cost is NOT a factor and you MUST have absolutely reliable ammunition (not range or plinking stuff) I would punch out the primers and start over.
    Now to get controversial. I doubt that oil will kill the primers in the short run, say a week or so. I tried to and never got a dead primer.
    I simply gently deprime as usual-do put on safety glasses as you should be doing anyway when you reload.
    I have deprimed literally hundreds of live primers without incident-I even re-use them in range ammo without problem.

    Hope it helps.
    Remember that the best lessons come from errors we make.
    I don't remember much about the patients that did well but remember everything when a case went sour.
    I bet you will not again make the tumbling with live primers mistake.

    Gary

  3. #3
    GunLoad Trainee
    Join Date
    Nov 2009
    Posts
    4

    Default

    Hansj,

    an addendum to the prior post- I forgot the obvious.

    put one of the primed cartridges in the old 30-30 and point it in a safe direction and pull the trigger before you stuff it with powder and bullet-if nothing else but to prove that the primers still work and I did not make a fool of myself in the prior posting.

    Do post what you do and the results if you could.

    Gary

  4. #4
    Spam Hammer fryboy's Avatar
    Join Date
    Feb 2010
    Location
    middle of america
    Posts
    116

    Default

    media can often clog the flash hole , super fine media can get into the primer , wont say that it wont fire but the flash hole mite be blocked , for the price of primers i'd consider it an in-expensive lesson and gently decap them , a universal decapping die would be wonderful for this just in case one does go off , it would then have some way to vent easier than in a tight fitting die with only the vent hole to vent , of course it goes without saying safety glasses are a must , if your ram has a slot facing you a small shield could also help prevent injury , some rams eject the primer to the side and some others down the ram ( those would be the best kind in this case but if you dont have one you dont have one )

  5. #5
    Great Master kodiak1's Avatar
    Join Date
    Dec 2005
    Location
    Alberta Territory
    Posts
    309

    Default

    hansj
    Take what gary wrote and listen to what he has told you.
    I have been doing this for 40 years and have done what you have done a couple of times.
    They all went bang. If the primer hole is plugged the minute you pull the trigger and the primer ignites the hole will come clean. This may hamper your burn a bit but it will go bang.
    The tiny amount of oil you got in, on or near that primer probably wont effect it at all.
    You can definetly deprime the cases and use new primers that is up to you.
    Have fun play safe and remember the lessons that you learn.
    The last part of the above statement is the hard part to do.

    Good Luck Ken.
    Ken.

    Love to Live, Live to Shoot!
    Live by the Gun...Die by the Gun...

  6. #6
    GunLoad Trainee
    Join Date
    Aug 2010
    Posts
    8

    Default

    I'm sure those will work for plinking.

    Now look at your mistake. Why did it happen? How could this be prevented? Work safe, pay attention, have fun, and shoot alot.

  7. #7
    GunLoad Trainee
    Join Date
    Feb 2011
    Posts
    8

    Default

    Sorry for taking so long to get back to my own post.

    Thanks Gary, and the rest of you as well.

    I have not done anything with them yet, but I will probably (after trying one unloaded primed brass in the rifle) just reload them and take them to the range for plinking. I am still waiting for my new Lee crimping die to come in before I do anything but I may just go out to the reloading shed and load them up, all but the crimp, and then crimp them all at the same time (I use a Dillon 550).

    As to how this happened. I recently inherited a HUGE amount of reloading/casting/shooting equipment and as a result it was necessary for me to completely reorganize my reloading shed. The primed brass was mistakenly placed with the fired brass and it wasn't noticed until we (my sons and I work together doing almost all of this stuff) were sorting the cleaned brass for sizing/depriming. So, in short, the whole of my reloading life was turned upside down and this was the result. We will not make this same mistake again!

    Oh, By the way, part of the inheritance (the dearly departed was not anyone I knew, he was a friend of a friend who knew I am a shooter/reloader) was the set of 30/30 dies (less the crimp) which I did not have. That is why 30/30 is a new reload for me.

    Hans

  8. #8
    GunLoad Trainee
    Join Date
    Apr 2011
    Location
    Mn
    Posts
    12

    Default

    Why are you tumbling primed brass? Not trying to bust your tail or nothing, just wondering. I tumble before priming. but that's just me. It just might clean out the primer pocket a bit.
    Endeavor to persevere: To exert oneself in an effort to persist in an undertaking in spite of counterinfluences, opposition, or discouragements.


    .

  9. #9
    Banned
    Join Date
    Apr 2011
    Posts
    33

    Default

    Hansj,
    Gary gave you the best advive and Kodiac1 reinforced it.
    Yhey should all shoot good as the primer explosion will clear the flash hole rather quickly.

    If you must ( or want to) deprime them and start over use a depriming die and remove the primers.
    I have done some 30/40 krag ammo that was 40 or more years old and deprimed them live that way.
    Didn't pop one primer. But have to be gentle and feel your way as you deprime.

    Good luck


    beekeeper

  10. #10
    GunLoad Trainee
    Join Date
    Mar 2005
    Posts
    8

    Default

    Quote Originally Posted by fryboy View Post
    media can often clog the flash hole , super fine media can get into the primer , wont say that it wont fire but the flash hole mite be blocked , for the price of primers i'd consider it an in-expensive lesson and gently decap them , a universal decapping die would be wonderful for this just in case one does go off , it would then have some way to vent easier than in a tight fitting die with only the vent hole to vent , of course it goes without saying safety glasses are a must , if your ram has a slot facing you a small shield could also help prevent injury , some rams eject the primer to the side and some others down the ram ( those would be the best kind in this case but if you dont have one you dont have one )
    X2 on this. For those of us who primed with the first Lee Loader hearing protection is amust as well.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check        

Gunloads.com Sponsored Links