Page 1 of 2 12 LastLast
Results 1 to 10 of 11

Thread: headspace on the mouth of the case???

  1. #1
    GunLoad Trainee
    Join Date
    Apr 2009
    Posts
    5

    Red face headspace on the mouth of the case???

    Exactly what does the term headspace on the mouth of the case mean, and what effect does crimp have on loads that headspace on the mouth of the case?

  2. #2
    runfiverun runfiverun's Avatar
    Join Date
    Dec 2007
    Location
    soda springs idaho
    Posts
    657

    Default

    when you headspace on the case mouth it means that you want your cases to be the same length.
    what is happening is that the case enters the chamber and stops at the end of the chamber,by the case hitting there.
    if you roll crimp a case that does this it will/can enter untill the crimp or the boolit engaging the rifling stops it.
    both situations can raise pressure, or affect your accuracy as will the longer shorter case.
    some guns will hold the shorter case by the extractor allowing it to still be fired but the case can be tipped in the chamber area and your bullet will enter the rifling at a shallow angle.
    this is why your pistol loads are taper crimped,there are some special cases where the 45 acp is roll crimped slightly but this is an accuracy thing and is pretty specialized.

  3. #3
    GunLoad Trainee
    Join Date
    May 2009
    Location
    Tucson
    Posts
    10

    Default

    Problem is that most auto cases are shorter than the chamber - measure and find out. On the .45, the main thing the crimp does is take out the bell put in previously. A light roll crimp does fine, and so does a taper crimp. Just seat the bullets out far enough to contact the leade of the rifling - when dropped into a dis-assembled barrel, the loaded round shoud be proud a smidgen. The slide slamming home will take care of business.
    Echo
    USAF Ret
    Distinguished Pistol Shot
    NRA Patron
    O&U

  4. #4

    Default

    This and that about calibers that headspace on the mouth of the case. Have questioned about it myself as I thought it was really important. Until I really understood the 45ACP headspaced on the mouth of the case I just loaded them up and fired them without a problem. After understanding, or questioning the fact the 45 should be trimmed to the correct length because it headspaces on the case mouth most replied they never trim their 45 cases and never will. I have never had a problem not trimming to specs. I am still up in the air about this fact myself and would like a clear answer.
    If a man has nothing greater to believe in than himself, he is a very lonely man.

  5. #5
    Ol Timer Sensai's Avatar
    Join Date
    May 2009
    Location
    Tidewater Virginia Area
    Posts
    17

    Default

    Most, if not all, rimless auto pistol cartridges are designed to headspace on the mouth of the case. If you look inside the chamber you will see the distinct point where the cartridge case mouth is supposed to be stopped. This is a 90 degree shoulder, rather than a taper. That being said, a lot of people use the end of the leade/ start of the rifling lands to headspace against. My biggest problem with this is that any change in bullit nose shape or seating depth, whether intentional or accidental, will change the headspace. I would rather have total control of the headspace by reloading the cartridge to fit my chamber. My preferred method of doing this is to get a good cast of my chamber and trim my cases to fit those measurements.
    Gary

    Takeoffs are optional, landings are manditory !!

  6. #6
    Dogs Like Him versifier's Avatar
    Join Date
    Dec 2005
    Location
    New Hampshire
    Posts
    1,854

    Default

    Most loaders never trim pistol cases. I know I don't. In theory, they headspace on the case mouth, but in practice, the extractor holds the case in place for the firing pin strike. The test of this is to remove the extractor and see for yourself that you will get mostly FTF's when you do as the round is pushed forward until the case mouth hits the front of the chamber and the firing pin cannot reach the primer. IME, the only time it may be critical is when you have a SA revolver chambered for a pistol round (like a Ruger Blackhawk with the interchangable .357/9mm cylinders), where the case actually does headspace on the mouth. Then you have to be careful your cases are long enough or you will get FTF's as you do in a pistol sans extractor. (The "star" extractor in a DA revolver will usually hold the cases in place for firing like that of the pistol.)
    "Stand your ground.
    Do not fire unless fired upon.
    But if they mean to have a war let it begin here."
    - Capt. Parker, Lexington Militia, April 19, 1775

  7. #7
    runfiverun runfiverun's Avatar
    Join Date
    Dec 2007
    Location
    soda springs idaho
    Posts
    657

    Default

    or you get a case too long and it binds the cylinder.
    same thing can happen to a pistol they will come to a halt short of battery and jam up.
    one way i keep my cases straight in the chamber is to use a cast boolit large enough to just slide in the chamber this helps align the boolit to the bbl. [this also gives resistance to the firing pin srike]
    same thing in a revolver i neck size my revolver brass [where the boolit goes only]
    so it is held in better alignment in the front of the cylinder and supported in the rear by the fireformed case.
    i have to thumb seat most of my cases in my revolvers.

  8. #8
    GunLoad Trainee
    Join Date
    May 2009
    Location
    Tucson
    Posts
    10

    Default

    Ed Harris called it end-play, that movement that exists due to the fact that the .45ACP case (for example) is several thousandths shorter than the chamber. Excessive end-play causes ignition variance, according to Mr. Harris. He suggests seating the boolit out .015-.020 so as to contact the leade and remove the end-play. I seat mine out a little further, maybe .050. Chambering will engrave the rifling on the boolit and end-play will be minimized.
    Echo
    USAF Ret
    Distinguished Pistol Shot
    NRA Patron
    O&U

  9. #9
    GunLoad Trainee
    Join Date
    Jun 2009
    Posts
    3

    Default

    I have never had a problem loading 45ACP, 40S&W, or 9mm which all headspace on the front of the cartridge case and I never trim those calibers. Most action pistol shooters, who may shoot many thousands of rounds in a year, don't trim either.

    I must take exception to the practice of headspacing on the bullet though! If there is no space between the bullet and rifling then pressures can soar and you could find yourself with a ruined pistol... or worse! Taper crimping to just the size of the factory specification case mouth diameter for the particular round is the recommended way to go. If the case has been properly full length resized anyway, this will insure enough bullet grip to prevent "setback" of the bullet while feeding and will not create an overpressure situation in the gun. You can load longer than the recommended cartridge OAL with no problems as long as the bullet is not actually forced into the rifling when feeding which is easy to check by loading a few rounds and dropping the slide on them then cycling them by hand and inspecting the unfired round to see if there are rifling marks on the bullet. If there are rifling marks seat them a little deeper until they no longer show any contact with the rifling. Let's not blow things up!

  10. #10

    Default

    Quote Originally Posted by JustSomeGuy View Post
    I have never had a problem loading 45ACP, 40S&W, or 9mm which all headspace on the front of the cartridge case and I never trim those calibers. Most action pistol shooters, who may shoot many thousands of rounds in a year, don't trim either.

    I must take exception to the practice of headspacing on the bullet though! If there is no space between the bullet and rifling then pressures can soar and you could find yourself with a ruined pistol... or worse! Taper crimping to just the size of the factory specification case mouth diameter for the particular round is the recommended way to go. If the case has been properly full length resized anyway, this will insure enough bullet grip to prevent "setback" of the bullet while feeding and will not create an overpressure situation in the gun. You can load longer than the recommended cartridge OAL with no problems as long as the bullet is not actually forced into the rifling when feeding which is easy to check by loading a few rounds and dropping the slide on them then cycling them by hand and inspecting the unfired round to see if there are rifling marks on the bullet. If there are rifling marks seat them a little deeper until they no longer show any contact with the rifling. Let's not blow things up!
    And that is a process that is called smoking the bullet. I would still like to see some type of pic or a reasonable post about cases like the 45, 9mm or 380 that is supposed to headspace on the mouth of the case and a resonable response as to why you can chamber the cases longer than SAMI Specs. I understand you may have to slug. But so many state they never trim their cases it still has me wondering.
    If a man has nothing greater to believe in than himself, he is a very lonely man.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check        

Gunloads.com Sponsored Links