Results 1 to 7 of 7

Thread: WTT Brass Need 5.6x50R(rimmed) for .44 Rem Mag or 30.06 Sprgfld.

  1. #1
    Grunt gemihur's Avatar
    Join Date
    Nov 2013
    Location
    Ridgelines of Virginia, Roanoke Valley
    Posts
    37

    Post WTT Brass Need 5.6x50R(rimmed) for .44 Rem Mag or 30.06 Sprgfld.

    Want To Trade Brass Need 5.6x50R(rimmed) or 357 Rem Max brass for .44 Rem Mag brass or 30.06 Sprgfld. brass all once fired
    my email: gemihur@yahoo.com
    Times is hard, I know!
    Lemme know if you can help
    Thanks,
    Jimmy
    Last edited by gemihur; 01-14-2014 at 01:11 AM.

  2. #2
    Dogs Like Him versifier's Avatar
    Join Date
    Dec 2005
    Location
    New Hampshire
    Posts
    1,854

    Default

    Savage Hi-Power ?
    "Stand your ground.
    Do not fire unless fired upon.
    But if they mean to have a war let it begin here."
    - Capt. Parker, Lexington Militia, April 19, 1775

  3. #3
    Grunt gemihur's Avatar
    Join Date
    Nov 2013
    Location
    Ridgelines of Virginia, Roanoke Valley
    Posts
    37

    Default

    Nope, gonna trim to 1.6" for 357 max
    Ya' gotta be resourceful in these 'dark days'.

  4. #4
    Grunt gemihur's Avatar
    Join Date
    Nov 2013
    Location
    Ridgelines of Virginia, Roanoke Valley
    Posts
    37

    Default

    357 Rem max brass seems to be such an unobtainable commodity these days that I've decided to go around my elbow to get to my ankle!
    .357 Remington maximum brass would be welcome !!! Honestly, It's Preferred !!!
    Last edited by gemihur; 01-14-2014 at 01:12 AM. Reason: clarify

  5. #5
    Dogs Like Him versifier's Avatar
    Join Date
    Dec 2005
    Location
    New Hampshire
    Posts
    1,854

    Default

    I am reading in the Handloader's Manual of Cartridge Conversions that there is no other factory case that will form to the dimensions of the .357MAX. Generally their advice is spot-on. Just curious as to where you were told you could make the cases out of 5.6x50R, base diameter is ok and you can maybe fudge the rim diameter a little, but the rim of the 5.6case is half the thickness of the Max's, enough I believe to prevent a firing pin strike on the primer. Let me know how your quest goes, I have a friend in a situation similar to yours.
    "Stand your ground.
    Do not fire unless fired upon.
    But if they mean to have a war let it begin here."
    - Capt. Parker, Lexington Militia, April 19, 1775

  6. #6
    Grunt gemihur's Avatar
    Join Date
    Nov 2013
    Location
    Ridgelines of Virginia, Roanoke Valley
    Posts
    37

    Default

    The Guru hisself Bellm! You know Mike? Gave me clearance for the process ...It went like this:Question: Mike,
    What is your opinion on the conversion and use of 5.6x50R (rimmed) brass to .357 Remington Maximum?
    Answer: Expensive but highly doable if you have some.
    Matter of fact, a couple of SHOT Shows back, I met with RWS at the SHOT Show and discussed that very thing with them as a possible source of Max. brass in the event nothing else developed. However, that year about 6 months after the show, we got an email from Nick Sache, head of the Remington brass mill, that they had done a run of brass. That staved off the shortage for awhile.
    Versi,
    I 'preciate your perspectives
    thanks for lookin' out for your fellow shooters ....I dread the trim session for any quantities, tho ... might use a Dremel cut-off to take the lion's share of shoulder & neck
    Last edited by gemihur; 01-15-2014 at 11:33 PM. Reason: correction

  7. #7
    Grunt gemihur's Avatar
    Join Date
    Nov 2013
    Location
    Ridgelines of Virginia, Roanoke Valley
    Posts
    37

    Default

    Thanks for the bump Gerald but I've about given up on locating the elusive European 5.6x50R brass. 'Spose it's all committed to all the drilling's owners
    I'm stocked now on 357 max anyway. Started this thread over five years ago, man.
    The 360 DW brass will get you through in a pinch. It's only 0.18" shorter. Just load 'em a little light
    Last edited by gemihur; 08-27-2019 at 12:49 PM.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check        

Gunloads.com Sponsored Links