Results 1 to 7 of 7

Thread: Scratching cases

  1. #1
    GunLoad Trainee
    Join Date
    Aug 2010
    Posts
    5

    Default Scratching cases

    Hey guys,

    I've been reloading my .44/40 for a couple of years now. Recently, I've been getting scratches on my cases. The scratches are coming from small bits of brass that seem to accumulate in the resizing die after I've run about 10 - 12 cases through.

    I've changed nothing in my process except to try a different set of dies...same problem. Any ideas?

    Thanks,
    Hedge

  2. #2
    runfiverun runfiverun's Avatar
    Join Date
    Dec 2007
    Location
    soda springs idaho
    Posts
    657

    Default

    the first thing to do is track down where the brass is coming from.
    am inclined to think it's tumbling media.
    the 44-40 is a tapered case you would get dents or a scuff in one spot and not along the length of the case.
    you might also have long cases and are knocking a bit of brass from the case mouth when sizing.
    i occasionally get a small ring of brass after trimming if i don't champher enough.

    but my first inclination is grit of some sort,and it is just looking like brass in the die.
    i have to be careful about dropping my brass around here as where i shoot it's lava rock finely ground and it will cling to brass, i especially have to check brass from my leverguns.

  3. #3
    GunLoad Trainee
    Join Date
    Aug 2010
    Posts
    5

    Default

    Makes a lot of sense, runfive.
    I know there's brass bits stuck in the die 'cause I've scraped them off. But you got me to thinking...small bits of grit shaving brass off the case and compounding the problem.

    I'll change my media and have a closer look at the case mouths.

    Thanks much!!

  4. #4
    Dogs Like Him versifier's Avatar
    Join Date
    Dec 2005
    Location
    New Hampshire
    Posts
    1,854

    Default

    Give the inside of the sizer a good polishing. It could be a poorly finished surface on the steel.

    Then you might think about not tumbling your cases. Usually a waste of time and an excellent way to raise the airborne particulate lead levels in your home.
    "Stand your ground.
    Do not fire unless fired upon.
    But if they mean to have a war let it begin here."
    - Capt. Parker, Lexington Militia, April 19, 1775

  5. #5
    GunLoad Trainee
    Join Date
    Aug 2010
    Posts
    5

    Default

    Sizer's been polished a few times already. Had to in order to get those brass chips out. It's slicker than snot on a door knob when I start.

    Cases get pretty dirty and tumbling is the easiest way to clean 'em. As for particulate matter,
    I keep the tumbler in the garage.

    Thanks for the input.

  6. #6
    GunLoad Trainee
    Join Date
    Aug 2010
    Posts
    5

    Default

    UPDATE

    Found the source of the problem. It's the vent hole in the die. Debris gets sucked back down
    the die and collects near the mouth of the die. The next case gets scratched and adds more debris.

    I cleaned the hole, swabbed out the die and ran through a bunch of cases with nary a scratch.

    Thanks for all the help, guys.

  7. #7
    GunLoad Trainee
    Join Date
    Jan 2011
    Location
    Washington State
    Posts
    6

    Default

    good info, haven't thought of that, I have a few dies with the vent, so I will be sure to clean them out every now an then..

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check        

Gunloads.com Sponsored Links